:

Salt Water Spray Tester	Reliability Environmental Test Measure Equipment
Forced Convection Dry Oven	Hydrogen Embrittlement Relief Oven
A Specimen Pretreatment Device	Other Equipment

·Features

Avaukabke to uniform spray inside Chamber!

※ Obtain European CE Certification(COC) → EUROPE (Germany) ‘TUV NORD’

* Registered No : K12802/E21

Accurate and uniform spray inside on chamber!

* Salt water spray tester is a material test equipment that inspects the wear and corrosion of products by spraying salt
water on organic film such as cast steel material plating pani t and inorganic film.

1. Using special nozzle,it is possible to spray mist particle and to spray evenly inside the chamber.

2. Satisfy the salt water spray(35℃±2℃)and CASS(50℃±2℃)test method.

3. Cycle operation is possible. →Timer and Counter Installation
Economical due to power-saving design.(1.1Kw)

4. The test space and exterior housing are made of non-corrosive materials.

5. Equipped with a microprocessor controller capable of self-diagnosis. (Optional Specifications)

6. Mount digital temperature controller, timer, buzzer, etc.

Chamber	Specimen Tray and Components		No.1 = Spray Tower No.2 = Funnel No.3 = V Type Support The V-type support depends on the weight of the specimen,It change into a strong and weak material. Maker = VISION TEC ROK.
After removing the support, spray tower	Spray Scene
Control Panel
Pressure gauge, regulator Thermometers, timers and various S/W.
Chamber Pressure	Pressure Gauge		*Normal range of pressure 0.07~0.17㎫ Maker=PARKER ROK.
Regulator		H →When increasing the pressure. L →When decreasing the pressure. Maker=PARKER ROK
Chamber	Over Heat Protector& Earth Leakage Breaker (OHP. ELB)		No.1 = Chamber O.H.P. No.2 = Saturaton Tank O.H.P. No.3 = E.L.B. Maker =LS ELECTRIC ROK.
Nozzle Inspection Window		It is possible to check whether the salt water is normally supplied from the salt water tank to the spray nozzle. Maker = VISION TEC ROK
Spray Nozzle		Nozzle Hole = 0.8 ~1.0Ø *Size and capacity of chamber and size of specimen Depending on the , the size of the nozzle and the quantity attached to it decide. Maker = VISION TEC ROK.
Spray Nozzle components
Salt Water Tank		Capacity 1.VT-ST100 =80ℓ 2.VT-ST200 =90ℓ 3.VT-ST300-66=120ℓ *Increase Salt Water Tank capacity depending on Chamber size. Maker = VISION TEC ROK
Chamber Heater		A heater that heats up the temperature in the chamber. Depending on the size and capacity of the chamber, the heaters will be able to the number increases and the capacity increases. Maker = VISION TEC ROK.
Chamber Optional Spec.	Dust Collector		of solids or liquids floating in a gas A device that collects and removes particulates. Create a pleasant indoor environment in the laboratory
Section View and Specification.		Model=MS 0500 Wind Volume = 7 CMM Constant pressure = 150~200mmAq Power = 0.38Kw(0.5HP) Weight = 25kG Filter 1st = Ceramic 2nd = Carbon 3rd = After Filter Maker: AUTO Link ROK.
Touch Screen (Optional Spec.)		1.The normal temperature in the chamber is 35±1℃. 2.Detects the temperature in the chamber. Maker = VISION TEC ROK.
Chamber General Spec.	Temperature Sensor		*Temp.Controller:Computer communi cation capabilities. 800x480 high resolution 7"TFT LCD screen Maker =NEX CONTROL ROK.
Chamber	Ion water manufacture device After producing 3000ℓ of ionic water,supplement the inner resin		Depending on the size and capacity of the chamber,the dimension of the cylinder of the device are increased
Control Valve		Standard Type 1 Max.Pressure : 10.5Bar,150psi 2 Max.Temp. : 50℃ (122˚F) 3 Min.Temp. : 1℃ (34˚F) 4 Max.Vacuum : 140mmHg 5 Capacity →(8x17) =11 ℓ 6 Out size : 220Ø x600mm Spec. vary depending on the size of the cylinder Maker =CJK ROK.
Saturator		Temperature saturator 45±1℃ Maker= VISION TEC ROK.
	Depending on the size and capacity of the chamber, the saturator will be able to the number increases and the capacity increases.
Solenoid Valve Appearance of attached solenoid valve		Specification No.1=220V 10W, 3/8 inch No.2=220V 5.5W,1/4 inch No.3=220V 8W ,1/4 inch Maker= PARKER ROK.
Solenoid Valve		*Solenoid valve is a device that opens the valve by the action of an electric current
Chamber Door	Automatic opening/closing door		VT-ST100 VT-ST200 VT-ST300-66 →Manual Door *VT-ST300-86 or Higher Model (Automatic opening/closing door)
For automatic opening/closing doors Air Cylinder		Working Type Double-Acting Type 1. Fluid : Air 2. Bearing Pressure : 15Kgf/㎠ 3. Max working pressure : 9.9Kgf/㎠ 4. Min working pressure : 0.5Kgf/㎠ 5. working speed : 50~500mm/s Maker : ISTC ROK. TPC ROK. The above is the basic type.

Chamber

Specimen Tray and Components

No.1 = Spray Tower
No.2 = Funnel
No.3 = V Type Support
The V-type support depends on the weight
of the specimen,It change into a strong and weak material.
Maker = VISION TEC ROK.

After removing the support, spray tower

Spray Scene

Control Panel

Pressure gauge, regulator Thermometers, timers and various S/W.

Chamber
Pressure

Pressure Gauge

*Normal range of pressure
0.07~0.17㎫
Maker=PARKER ROK.

Regulator

H →When increasing the pressure.
L →When decreasing the pressure.
Maker=PARKER ROK

Chamber

Over Heat Protector&
Earth Leakage Breaker
(OHP. ELB)

No.1 = Chamber O.H.P.
No.2 = Saturaton Tank O.H.P.
No.3 = E.L.B.
Maker =LS ELECTRIC ROK.

Nozzle Inspection Window

It is possible to check whether the salt water is normally
supplied from the salt water tank to the spray nozzle.
Maker = VISION TEC ROK

Spray Nozzle

Nozzle Hole = 0.8 ~1.0Ø
*Size and capacity of chamber and size of specimen
Depending on the , the size of the nozzle and the quantity
attached to it decide.
Maker = VISION TEC ROK.

Spray Nozzle components

Salt Water Tank

Capacity
1.VT-ST100 =80ℓ
2.VT-ST200 =90ℓ
3.VT-ST300-66=120ℓ
*Increase Salt Water Tank capacity
depending on Chamber size.
Maker = VISION TEC ROK

Chamber Heater

A heater that heats up the
temperature in the chamber.
Depending on the size and capacity
of the chamber, the heaters will be
able to the number increases and
the capacity increases.
Maker = VISION TEC ROK.

Chamber
Optional Spec.

Dust Collector

of solids or liquids floating in a gas
A device that collects and
removes particulates.
Create a pleasant indoor
environment in the laboratory

Section View and Specification.

Model=MS 0500
Wind Volume = 7 CMM
Constant pressure = 150~200mmAq
Power = 0.38Kw(0.5HP)
Weight = 25kG
Filter 1st = Ceramic
2nd = Carbon
3rd = After Filter
Maker: AUTO Link ROK.

Touch Screen
(Optional Spec.)

1.The normal temperature in the chamber is 35±1℃.
2.Detects the temperature in the chamber.
Maker = VISION TEC ROK.

Chamber
General Spec.

Temperature Sensor

*Temp.Controller:Computer
communi cation capabilities.
800x480 high resolution 7"TFT LCD screen
Maker =NEX CONTROL ROK.

Chamber

Ion water manufacture device
After producing 3000ℓ of
ionic water,supplement
the inner resin

Depending on the size and capacity
of the chamber,the dimension
of the cylinder of the device are increased

Control Valve

Standard Type
1 Max.Pressure : 10.5Bar,150psi
2 Max.Temp. : 50℃ (122˚F)
3 Min.Temp. : 1℃ (34˚F)
4 Max.Vacuum : 140mmHg
5 Capacity →(8x17) =11 ℓ
6 Out size : 220Ø x600mm
*Spec. vary depending on the size of the cylinder
*Maker =CJK ROK.

Saturator

Temperature saturator 45±1℃
Maker= VISION TEC ROK.

Depending on the size and capacity
of the chamber, the saturator will
be able to the number increases
and the capacity increases.

Solenoid Valve
Appearance of attached
solenoid valve

Specification
No.1=220V
10W, 3/8 inch
No.2=220V
5.5W,1/4 inch
No.3=220V
8W ,1/4 inch
Maker= PARKER ROK.

Solenoid Valve

*Solenoid valve is a device that
opens the valve by the action of an
electric current

Chamber
Door

Automatic opening/closing door

VT-ST100
VT-ST200
VT-ST300-66 →Manual Door
*VT-ST300-86 or Higher Model
(Automatic opening/closing door)

For automatic opening/closing doors Air Cylinder

*Working Type
Double-Acting Type
1. Fluid : Air
2. Bearing Pressure : 15Kgf/㎠
3. Max working pressure : 9.9Kgf/㎠
4. Min working pressure : 0.5Kgf/㎠
5. working speed : 50~500mm/s
Maker : ISTC ROK. TPC ROK.
*The above is the basic type.

MODEL	VT-ST300-86	VT-ST400-86	VT-ST400-86
Temperature Range	RT ~35℃ (*RT ~ 60℃→Can be changed by customer order=Select Option)
Tester Method	Neutral Spray Test
Tester Temperature	Neutral(35℃±2℃)/CASS (50℃±2℃) Option
Temperature Control	Digital P.I.D. Control
Spray Volume	1.5±0.5㎖/80㎠/h (Mean Value of 24 Hours Operation)
Material In	PVC 8t
Material Out	SUS 304
Door	PVC Transparent
Dimension In (WxDxH)	1200 x800 x 600mm	1500 x 800 x 600mm	2000 x 800 x 600mm
Dimension Out (WxDxH)	2150 x1100 x 1600mm	2400 x 1100 x 1600mm	2900 x 1100 x 1600mm
Heater Capacity	Chamber:1.0Kw,Saturation Tank:0.5Kw	Chamber:1.4Kw,Saturation Tank:0.5Kw	Chamber:1.0Kw(2),Saturation Tank:0.5Kw
Safety Device	ELB.OHP
Power Source	AC220V 1Ø /50/60 Hz
Air Cylinder for Door Open	Free(Basis)
CASS	Option
Touch Screen	Option
* Other specifications can be made to order * External appearance & type and specifiation may be to change without advance notice to enhance the performance of equipment.

MODEL

VT-ST300-86

VT-ST400-86

Temperature Range

RT ~35℃ (*RT ~ 60℃→Can be changed by customer order=Select Option)

Tester Method

Neutral Spray Test

Tester Temperature

Neutral(35℃±2℃)/CASS (50℃±2℃) Option

Temperature Control

Digital P.I.D. Control

Spray Volume

1.5±0.5㎖/80㎠/h (Mean Value of 24 Hours Operation)

Material In

PVC 8t

Material Out

SUS 304

Door

PVC Transparent

Dimension In (WxDxH)

1200 x800 x 600mm

1500 x 800 x 600mm

2000 x 800 x 600mm

Dimension Out (WxDxH)

2150 x1100 x 1600mm

2400 x 1100 x 1600mm

2900 x 1100 x 1600mm

Heater Capacity

Chamber:1.0Kw,Saturation
Tank:0.5Kw

Chamber:1.4Kw,Saturation
Tank:0.5Kw

Chamber:1.0Kw(2),Saturation
Tank:0.5Kw

Safety Device

ELB.OHP

Power Source

AC220V 1Ø /50/60 Hz

Air Cylinder for Door Open

Free(Basis)

CASS

Option

Touch Screen

Option

* Other specifications can be made to order

* External appearance & type and specifiation may be to change without advance notice to enhance the performance of equipment.